Samsung Galaxy J4 J400MUBSECUL1
SM-J400M 2 countries Android 10

Samsung Galaxy J4 J400MUBSECUL1 Firmware

Samsung Galaxy J4 J400MUBSECUL1 is an Android 10 firmware for Argentina (PSN), Puerto Rico (PCT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J400MUBSDCUK3: bootloader binary raised from D (13) to E (14), so after installing it there is no way back to older builds; security patch 2021-12-01 instead of 2021-11-01. A newer build for SM-J400M is available: J400MUBUECWC1.

Download firmware
8.8/10 (495)8,956 times
Android 10
OS Version
2022-01-14
First release
other regions until 2022-01-19
2021-12-01
Security patch
2
Countries
2
CSC codes
E (14)
Bootloader binary

Bootloader binary E (14). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: J400MUBSECUL1
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-J400M
    PCT Puerto Rico
    		J400MOWAECUL7 2022-01-14 2022-01-18 2.534 GiB
    SM-J400M_2_20211224174900_oddat4a4cr_fac.zip
    		Download
    SM-J400M
    PSN Argentina
    		J400MOWBECUL8 2022-01-19 2022-01-20 2.518 GiB
    SM-J400M_2_20211230235730_nklkqnp3o8_fac.zip
    		Download

    No matching downloads

    How to flash J400MUBSECUL1

    • J400MUBSECUL1 has bootloader binary E (14). Your device must run binary E (14) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    What's new in J400MUBSECUL1

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    Rollout of J400MUBSECUL1 by region

    First release
    January 18, 2022
    Last region
    January 20, 2022
    Duration
    3 days
    Regions
    2
    1. Day 1 · · 1 region
      Puerto RicoPCT
    2. Day 3 · · 1 region
      ArgentinaPSN

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution720 x 1280 pixels
    • Display typeSAMOLED
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3000 mAh
    • Weight175 g

    Specifications of SM-J400F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J400MUBSECUL1 is Android 10 firmware for Samsung Galaxy J4, released for Argentina (PSN), Puerto Rico (PCT). It includes the 2021-12-01 security patch. Samsung built it on 2022-01-14.

    No. A newer build for SM-J400M is available: J400MUBUECWC1. Install it instead of J400MUBSECUL1 unless you need this exact version. The previous build was J400MUBSDCUK3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J4 must be on bootloader binary E (14) or lower.

    This build uses bootloader binary E (14). It can be flashed on a Samsung Galaxy J4 running binary E (14) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 10 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J4

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · Security patch update

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    • The security of your device has been improved.

    • Added new feature. - Google RCS(Rich Communication Service)
    • Overall stability of functions improved.
    • The security of your device has been improved.

    Show 6 older builds

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    • LGPD (General Personal Data Protection Law) has been applied.
    • The security of your device has been improved.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    One UI 2 upgrade with Android 10

    One UI 2 brings you Android 10, with exciting new features from Samsung and Google based on feedback from users like you.
    We recommend that you back up your important data to keep it safe during the upgrade.
    Some apps, including Calculator, Samsung Internet, Samsung Health and Samsung Notes, need to be updated individually after you update your OS.

    Here's what's new.

    Dark mode
    - Enhanced image, text, and color adjustments for day and night environments.
    - Dark...

    Model firmware by region