Samsung Galaxy J6 J600GDXU6CTB3
SM-J600G 10 countries Android 9 (Pie)

Samsung Galaxy J6 J600GDXU6CTB3 Firmware

Samsung Galaxy J6 J600GDXU6CTB3 is an Android 9 (Pie) firmware for 10 countries, 10 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J600GUBS6BTC2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J600G is available: J600GDXUACZB1.

Download firmware
9.2/10 (455)43,550 times
Android 9 (Pie)
OS Version
10
Countries
10
CSC codes
6
Bootloader binary

Bootloader binary 6. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J6 use bootloader binary A (10) (latest: J600GDXUACZB1). If your device already runs binary A (10), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    10
    MODEM/CP Version: J600GDXU6CTB3
    ModelRegionCSC VersionSizeFile nameDownload
    SM-J600G
    BRI Taiwan
    		J600GOLM6CTB3 — —
    SM-J600G
    CAM Cambodia
    		J600GOLM6CTB3 — —
    SM-J600G
    LAO Laos
    		J600GOLM6CTB3 — —
    SM-J600G
    MYM Myanmar (Burma)
    		J600GOLM6CTB3 — —
    SM-J600G
    THL Thailand
    		J600GOLM6CTB3 — —
    SM-J600G
    VNZ New Zealand
    		J600GOLM6CTB3 — —
    SM-J600G
    XME Malaysia
    		J600GOLM6CTB3 — —
    SM-J600G
    XSP Singapore
    		J600GOLM6CTB3 — —
    SM-J600G
    XTC Philippines
    		J600GOLM6CTB3 — —
    SM-J600G
    XXV Vietnam
    		J600GOLM6CTB3 — —

    No matching downloads

    How to flash J600GDXU6CTB3

    • J600GDXU6CTB3 has bootloader binary 6. Your device must run binary 6 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 8.0
    • Display diagonal14.2 cm (5.6")
    • Display resolution720 x 1480 pixels
    • Display typeSAMOLED
    • Processor frequency1.6 GHz
    • Processor familySamsung Exynos
    • Processor model7870
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity3000 mAh
    • Weight154 g

    Frequently Asked Questions

    J600GDXU6CTB3 is Android 9 (Pie) firmware for Samsung Galaxy J6, released for 10 countries, 10 CSC codes.

    No. A newer build for SM-J600G is available: J600GDXUACZB1. Install it instead of J600GDXU6CTB3 unless you need this exact version. The previous build was J600GUBS6BTC2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J6 must be on bootloader binary 6 or lower.

    This build uses bootloader binary 6. It can be flashed on a Samsung Galaxy J6 running binary 6 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 11 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J6

    • Stability and reliability
    Device behavior has been improved.

    These changes may vary depending on the model, country, or network operator of the customer environment.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    • The security of your device has been improved.

    • The latest Android security patch has been applied.
    - Device security has been further enhanced.

    • The security of your device has been improved.

    Show 11 older builds

    • The stability of Camera has been improved.
    • Overall stability of your device has been improved.
    • The security of your device has been improved.

    • The security of your device has been improved.

    • The latest Android security patch has been applied.
    - Device security has been further enhanced.

    • Overall stability of functions improved.

    • The stability of Camera has been improved.
    • Overall stability of your device has been improved.
    • The security of your device has been improved.

    • The stability of Camera has been improved.
    • Added new feature. - Google RCS(Rich Communication Service)
    • The security of your device has been improved.

    · The security of your device has been improved.

    · Security patch update

    - The latest Android security patch has been applied.
    ㆍDevice security has been further enhanced.

    · The security of your device has been improved.

    Model firmware by region