Samsung Galaxy J6 J600GUBS6BTB3
SM-J600G 5 countries Android 9 (Pie)

Samsung Galaxy J6 J600GUBS6BTB3 Firmware

Samsung Galaxy J6 J600GUBS6BTB3 is an Android 9 (Pie) firmware for 5 countries, 5 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J600GDXS6BTB2: security patch 2020-03-01 instead of 2020-02-01. A newer build for SM-J600G is available: J600GDXUACZB1.

Download firmware
9.0/10 (462)21,985 times
Android 9 (Pie)
OS Version
2020-02-14
First release
other regions until 2020-02-29
2020-03-01
Security patch
5
Countries
5
CSC codes
6
Bootloader binary

Bootloader binary 6. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J6 use bootloader binary A (10) (latest: J600GDXUACZB1). If your device already runs binary A (10), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-J600G
    ALE Ecuador
    BVV Bolivia
    DOR Dominican Republic
    		J600GOWE6BTB3J600GDXS6BTB3 2020-02-29 2020-03-09 3.479 GiB
    SM-J600G_2_20220421014121_ui79zh67i2_fac.zip
    		Download
    SM-J600G
    CHX Chile
    		J600GOWE6BTB3J600GUBS6BTB3 2020-02-14 2020-03-05 — — Download
    SM-J600G
    MXO Mexico
    		J600GOWO6BTB3J600GUBS6BTB3 2020-02-14 2020-03-08 — — Download

    No matching downloads

    How to flash J600GUBS6BTB3

    • J600GUBS6BTB3 has bootloader binary 6. Your device must run binary 6 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    What's new in J600GUBS6BTB3

    · The security of your device has been improved.

    Rollout of J600GUBS6BTB3 by region

    First release
    March 5, 2020
    Last region
    March 18, 2020
    Duration
    14 days
    Regions
    5
    1. Day 1 · · 1 region
      ChileCHX
    2. Day 4 · · 1 region
      MexicoMXO
    3. Day 5 · · 1 region
      Dominican RepublicDOR
    4. Day 12 · · 1 region
      BoliviaBVV
    5. Day 14 · · 1 region
      EcuadorALE

    Device specifications

    • Launched withAndroid 8.0
    • Display diagonal14.2 cm (5.6")
    • Display resolution720 x 1480 pixels
    • Display typeSAMOLED
    • Processor frequency1.6 GHz
    • Processor familySamsung Exynos
    • Processor model7870
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity3000 mAh
    • Weight154 g

    Frequently Asked Questions

    J600GUBS6BTB3 is Android 9 (Pie) firmware for Samsung Galaxy J6, released for 5 countries, 5 CSC codes. It includes the 2020-03-01 security patch. Samsung built it on 2020-02-14.

    No. A newer build for SM-J600G is available: J600GDXUACZB1. Install it instead of J600GUBS6BTB3 unless you need this exact version. The previous build was J600GDXS6BTB2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 3.479 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J6 must be on bootloader binary 6 or lower.

    This build uses bootloader binary 6. It can be flashed on a Samsung Galaxy J6 running binary 6 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 11 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J6

    • Stability and reliability
    Device behavior has been improved.

    These changes may vary depending on the model, country, or network operator of the customer environment.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    • The security of your device has been improved.

    • The latest Android security patch has been applied.
    - Device security has been further enhanced.

    • The security of your device has been improved.

    Show 11 older builds

    • The stability of Camera has been improved.
    • Overall stability of your device has been improved.
    • The security of your device has been improved.

    • The security of your device has been improved.

    • The latest Android security patch has been applied.
    - Device security has been further enhanced.

    • Overall stability of functions improved.

    • The stability of Camera has been improved.
    • Overall stability of your device has been improved.
    • The security of your device has been improved.

    • The stability of Camera has been improved.
    • Added new feature. - Google RCS(Rich Communication Service)
    • The security of your device has been improved.

    · The security of your device has been improved.

    · Security patch update

    - The latest Android security patch has been applied.
    ㆍDevice security has been further enhanced.

    · The security of your device has been improved.

    Model firmware by region