SM-J700H 2 countries Android 6.0.1 (Marshmallow)

Samsung Galaxy J7 J700HXXU2BPFD Firmware

Name: Samsung Galaxy J7 (SM-J700H)
Brand: Samsung
Availability: InStock

Samsung Galaxy J7 J700HXXU2BPFD is an Android 6.0.1 (Marshmallow) firmware for Myanmar (Burma) (MYM), Vietnam (XXV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J700HXXU2BPFB https://samfirm.shop/build/J700HXXU2BPFB, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J700H is available: J700HXWU3BVH1 https://samfirm.shop/build/J700HXWU3BVH1.

Download firmware 8.7/10 (463)8,649 times

Android 6.0.1 (Marshmallow)

OS Version

2016-06-22

Build Date

Countries

CSC codes

Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J7 use bootloader binary 3 (latest: J700HXWU3BVH1). If your device already runs binary 3, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: J700HXXU2BPFD

Model	Region	CSC Version	Size	File name	Download
SM-J700H	MYM Myanmar (Burma)	J700HOLB2BPF3	—	—	Download
SM-J700H	XXV Vietnam	J700HOLB2BPF3	—	—	Download

How to flash J700HXXU2BPFD

J700HXXU2BPFD has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

J700HXXU2BPFD is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy J7, released for Myanmar (Burma) (MYM), Vietnam (XXV). Samsung built it on 2016-06-22.

No. A newer build for SM-J700H is available: J700HXWU3BVH1. Install it instead of J700HXXU2BPFD unless you need this exact version. The previous build was J700HXXU2BPFB.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J7 must be on bootloader binary 2 or lower.

This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J7 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 26 other builds of this model use the same binary, so you can switch between them in both directions.