Samsung Galaxy J7(2015) J700PVPS1AQF3
SM-J700P 1 country Android 6.0.1 (Marshmallow)

Samsung Galaxy J7(2015) J700PVPS1AQF3 Firmware

Samsung Galaxy J7(2015) J700PVPS1AQF3 is an Android 6.0.1 (Marshmallow) firmware for United States (BST, SPR, VMU, XAS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J700PVPS1AQA2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J700P is available: J700PVPU2BQJ2.

Download firmware
8.8/10 (43)13,355 times
Android 6.0.1 (Marshmallow)
OS Version
2017-06-21
First release
other regions until 2017-07-04
1
Countries
4
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J7(2015) use bootloader binary 2 (latest: J700PVPU2BQJ2). If your device already runs binary 2, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J700PVPS1AQF3
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-J700P
    BST, SPR, VMU United States
    		J700PSPT1AQF3 2017-06-21 2017-07-24 1.613 GiB
    SM-J700P_1_20171204091414_8wfo5ce0ax_fac.zip
    		Download
    SM-J700P
    XAS United States
    		J700PSPT1AQF3 2017-07-04 2017-07-24 1.443 GiB
    SM-J700P_1_20170704142152_krmsr3tvfb_fac.zip
    		Download

    No matching downloads

    How to flash J700PVPS1AQF3

    • J700PVPS1AQF3 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J700PVPS1AQF3 by region

    Samsung released this build in all regions (4) on the same day, July 24, 2017.

    Frequently Asked Questions

    J700PVPS1AQF3 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy J7(2015), released for United States (BST, SPR, VMU, XAS). Samsung built it on 2017-06-21.

    No. A newer build for SM-J700P is available: J700PVPU2BQJ2. Install it instead of J700PVPS1AQF3 unless you need this exact version. The previous build was J700PVPS1AQA2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J7(2015) must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy J7(2015) running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 5 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7(2015)

    No changelog details available.
    Model firmware by region