Samsung Galaxy J7 Neo J701MUBSACUB1
SM-J701M 1 country Android 9 (Pie)

Samsung Galaxy J7 Neo J701MUBSACUB1 Firmware

Samsung Galaxy J7 Neo J701MUBSACUB1 is an Android 9 (Pie) firmware for Mexico (TCE). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J701MUBSACUA3, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J701M is available: J701MUBUBCZC2.

9.2/10 (460)4,468 times
Android 9 (Pie)
OS Version
2021-03-02
Build Date
n/a
Security patch
1
Countries
1
CSC codes
A (10)
Bootloader binary

Bootloader binary A (10). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J7 Neo use bootloader binary B (11) (latest: J701MUBUBCZC2). If your device already runs binary B (11), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J701MUBSACUA2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J701M
    TCE Mexico
    		J701MTCEACUA1 2021-03-04 2.767 GiB
    SM-J701M_1_20210219074305_xqtda3j5z4_fac.zip

    No matching downloads

    How to flash J701MUBSACUB1

    • J701MUBSACUB1 has bootloader binary A (10). Your device must run binary A (10) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 7.0
    • Display diagonal14 cm (5.5")
    • Display resolution720 x 1280 pixels
    • Display typeSAMOLED
    • Processor frequency1.6 GHz
    • Processor familySamsung Exynos
    • Processor model7870
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity3000 mAh
    • Weight170 g

    Frequently Asked Questions

    J701MUBSACUB1 is Android 9 (Pie) firmware for Samsung Galaxy J7 Neo, released for Mexico (TCE). Samsung built it on 2021-03-02.

    No. A newer build for SM-J701M is available: J701MUBUBCZC2. Install it instead of J701MUBSACUB1 unless you need this exact version. The previous build was J701MUBSACUA3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.767 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J7 Neo must be on bootloader binary A (10) or lower.

    This build uses bootloader binary A (10). It can be flashed on a Samsung Galaxy J7 Neo running binary A (10) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7 Neo

    No changelog details available.
    Model firmware by region