Samsung Galaxy J7 Pro J730GUBSDCTL3
SM-J730G 2 countries Android 9 (Pie)

Samsung Galaxy J7 Pro J730GUBSDCTL3 Firmware

Samsung Galaxy J7 Pro J730GUBSDCTL3 is an Android 9 (Pie) firmware for Bolivia (BVO), Trinidad & Tobago (EON). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J730GUBSCCTI5: bootloader binary raised from C (12) to D (13), so after installing it there is no way back to older builds. A newer build for SM-J730G is available: J730GUBUDCUG1.

8.9/10 (477)8,933 times
Android 9 (Pie)
OS Version
2020-12-29
Build Date
n/a
Security patch
2
Countries
2
CSC codes
D (13)
Bootloader binary

Bootloader binary D (13). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J730GUBSDCTL3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J730G
    BVO Bolivia
    EON Trinidad & Tobago
    		J730GUUBDCTL1 2020-12-29 1.912 GiB
    SM-J730G_1_20201218212204_mh37hcsxmb_fac.zip

    No matching downloads

    How to flash J730GUBSDCTL3

    • J730GUBSDCTL3 has bootloader binary D (13). Your device must run binary D (13) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J730GUBSDCTL3 by region

    Samsung released this build in all regions (2) on the same day, December 29, 2020.

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1920 x 1080 pixels
    • Display typeSAMOLED
    • Processor frequency1.6 GHz
    • RAM3 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity3600 mAh
    • Weight181 g

    Frequently Asked Questions

    J730GUBSDCTL3 is Android 9 (Pie) firmware for Samsung Galaxy J7 Pro, released for Bolivia (BVO), Trinidad & Tobago (EON). Samsung built it on 2020-12-29.

    No. A newer build for SM-J730G is available: J730GUBUDCUG1. Install it instead of J730GUBSDCTL3 unless you need this exact version. The previous build was J730GUBSCCTI5.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.912 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J7 Pro must be on bootloader binary D (13) or lower.

    This build uses bootloader binary D (13). It can be flashed on a Samsung Galaxy J7 Pro running binary D (13) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 11 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7 Pro

    No changelog details available.
    Model firmware by region