Samsung Watch8 40mm L325USQU1AYFE

Samsung Watch8 40mm L325USQU1AYFE Firmware

Samsung Watch8 40mm L325USQU1AYFE is an Android 16 firmware for United States (XAA). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. A newer build for SM-L325U is available: L325USQS3AZF4 https://samfirm.shop/build/L325USQS3AZF4.

Download firmware
9.2/10 (33)186 times
Android 16
OS Version
2025-07-16
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Watch8 40mm use bootloader binary 3 (latest: L325USQS3AZF4 https://samfirm.shop/build/L325USQS3AZF4). If your device already runs binary 3, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: L325USQU1AYFE
    ModelRegionCSC VersionSizeFile nameDownload
    SM-L325U
    XAA United States
    L325UOYM1AYFE 3.721 GiB
    SM-L325U_1_20250716131341_qwx5jll365_fac.zip
    Download

    No matching downloads

    How to flash L325USQU1AYFE

    • L325USQU1AYFE has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withWear OS
    • Display diagonal3.3 cm (1.3")
    • Display technologyAMOLED
    • Display resolution438 x 438 pixels
    • RAM2000 MB
    • Flash memory32 GB
    • Battery capacity425 mAh
    • Weight30 g
    • Band colourGraphite

    Specifications of SM-L325F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    L325USQU1AYFE is Android 16 firmware for Samsung Watch8 40mm, released for United States (XAA). Samsung built it on 2025-07-16.

    No. A newer build for SM-L325U is available: L325USQS3AZF4. Install it instead of L325USQU1AYFE unless you need this exact version.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 3.721 GiB; keep about twice that free on the computer to unzip it. The Samsung Watch8 40mm must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Watch8 40mm running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Watch8 40mm

    https://samfirm.shop/build/L325USQS3AZF4

    • Security
    The device is protected with improved security.

    These changes may vary depending on the model, country, or network operator of the customer environment.

    https://samfirm.shop/build/L325USQU3AZB4

    • Stability and reliability
    Device behavior has been improved.
    • Security
    The device is protected with improved security.

    These changes may vary depending on the model, country, or network operator of the customer environment.

    https://samfirm.shop/build/L325USQS1AYH6

    • Stability and reliability
    Device behavior has been improved.

    These changes may vary depending on the model, country, or network operator of the customer environment.

    No changelog details available.