Samsung Galaxy S 3 LTE (Sprint) L710VPUCOJ1
SPH-L710 1 country Android 4.4.2

Samsung Galaxy S 3 LTE (Sprint) L710VPUCOJ1 Firmware

Samsung Galaxy S 3 LTE (Sprint) L710VPUCOJ1 is an Android 4.4.2 firmware for United States (BST, VMU, XAS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build L710VPUBMK5, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SPH-L710 is available: L710VPUDNJ2.

Download firmware
9.0/10 (461)13,000 times
Android 4.4.2
OS Version
2015-10-14
Build Date
1
Countries
3
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: L710VPUCOJ1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SPH-L710
    BST, VMU, XAS United States
    		L710SPTCOJ1 2015-11-24 960.583 MiB
    SPH-L710_1_20151124144540_1krgvbh7j7_fac.zip
    		Download

    No matching downloads

    How to flash L710VPUCOJ1

    • L710VPUCOJ1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of L710VPUCOJ1 by region

    Samsung released this build in all regions (3) on the same day, November 24, 2015.

    Frequently Asked Questions

    L710VPUCOJ1 is Android 4.4.2 firmware for Samsung Galaxy S 3 LTE (Sprint), released for United States (BST, VMU, XAS). Samsung built it on 2015-10-14.

    No. A newer build for SPH-L710 is available: L710VPUDNJ2. Install it instead of L710VPUCOJ1 unless you need this exact version. The previous build was L710VPUBMK5.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 960.583 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S 3 LTE (Sprint) must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S 3 LTE (Sprint) running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S 3 LTE (Sprint)

    No changelog details available.
    Model firmware by region