SM-M105G 3 countries Android 8.1.0 (Pie)

Samsung Galaxy M10 M105GDXU1ASBD Firmware

Name: Samsung Galaxy M10 (SM-M105G)
Brand: Samsung
Availability: InStock

Samsung Galaxy M10 M105GDXU1ASBD is an Android 8.1.0 (Pie) firmware for Indonesia (XID), Malaysia (XME), Vietnam (XEV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build M105GPUU1ASBD https://samfirm.shop/build/M105GPUU1ASBD: Android updated from Android 8.1.0 to Android 8.1.0 (Pie). A newer build for SM-M105G is available: M105GDXSACWA1 https://samfirm.shop/build/M105GDXSACWA1.

8.7/10 (453)12,996 times

Android 8.1.0 (Pie)

OS Version

2019-02-22

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy M10 use bootloader binary A (10) (latest: M105GDXSACWA1). If your device already runs binary A (10), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: M105GDXU1ASBD

Model	Region	CSC Version	Size	File name
SM-M105G	XEV Vietnam	M105GOLM1ASBD	—	—
SM-M105G	XID Indonesia	M105GOLE1ASBD	—	—
SM-M105G	XME Malaysia	M105GOLM1ASBD	—	—

Device specifications

Display diagonal15.8 cm (6.2")
Display resolution720 x 1520 pixels
Display typeTFT
RAM2 GB
Rear camera resolution13 MP
Rear camera typeDual camera
Battery capacity3400 mAh
Weight163 g

Specifications of SM-M105, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash M105GDXU1ASBD

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

M105GDXU1ASBD has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

M105GDXU1ASBD is Android 8.1.0 (Pie) firmware for Samsung Galaxy M10, released for Indonesia (XID), Malaysia (XME), Vietnam (XEV). Samsung built it on 2019-02-22.

No. A newer build for SM-M105G is available: M105GDXSACWA1. Install it instead of M105GDXU1ASBD unless you need this exact version. The previous build was M105GPUU1ASBD.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy M10 must be on bootloader binary 1 or lower.

This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy M10 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 8 other builds of this model use the same binary, so you can switch between them in both directions.