Samsung Galaxy Note 2 (International) N7100XXSFQAC
GT-N7100 1 country Android 4.4.2 (Jelly)

Samsung Galaxy Note 2 (International) N7100XXSFQAC Firmware

Samsung Galaxy Note 2 (International) N7100XXSFQAC is an Android 4.4.2 (Jelly) firmware for United Kingdom (O2U). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N7100XXSFQAB: Android updated from Android 4.4.2 (KitKat) to Android 4.4.2 (Jelly). A newer build for GT-N7100 is available: N7100XXDMG1.

Download firmware
8.7/10 (460)4,501 times
Android 4.4.2 (Jelly)
OS Version
1
Countries
1
CSC codes
S (28)
Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note 2 (International) use bootloader binary X (33) (latest: N7100XXDMG1). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: N7100XXUFNG1
    ModelRegionCSC VersionSizeFile nameDownload
    GT-N7100
    O2U United Kingdom
    		N7100O2UFNJ1 — — Download

    No matching downloads

    How to flash N7100XXSFQAC

    • N7100XXSFQAC has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 4.1
    • Display diagonal14.1 cm (5.55")
    • Display resolution1280 x 720 pixels
    • Display typeSAMOLED
    • Processor frequency1.6 GHz
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity3100 mAh
    • Weight181.6 g

    Frequently Asked Questions

    N7100XXSFQAC is Android 4.4.2 (Jelly) firmware for Samsung Galaxy Note 2 (International), released for United Kingdom (O2U).

    No. A newer build for GT-N7100 is available: N7100XXDMG1. Install it instead of N7100XXSFQAC unless you need this exact version. The previous build was N7100XXSFQAB.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note 2 (International) must be on bootloader binary S (28) or lower.

    This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Note 2 (International) running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 17 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note 2 (International)

    No changelog details available.
    Model firmware by region