Samsung Galaxy Note3 Neo N750XXUDPA3
SM-N750 4 countries Android 5.1.1 (Lollipop)

Samsung Galaxy Note3 Neo N750XXUDPA3 Firmware

Samsung Galaxy Note3 Neo N750XXUDPA3 is an Android 5.1.1 (Lollipop) firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N750XXUDPA2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. This is the newest build for SM-N750.

Download firmware
8.7/10 (28)17,975 times
Android 5.1.1 (Lollipop)
OS Version
2016-01-27
First release
other regions until 2016-02-22
4
Countries
4
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-N750
    CAM Cambodia
    		N750OLBDPA1N750XXUDOK1 2016-02-22 2016-02-22 1.274 GiB
    SM-N750_1_20160222153253_vn16qopijn_fac.zip
    		Download
    SM-N750
    CAM Cambodia
    		N750OLBDPA1N750XXUDPA3 2016-01-27 — — — Download
    SM-N750
    XME Malaysia
    XSE Indonesia
    XXV Vietnam
    		N750OLBDPA1N750XXUDOK1 2016-01-27 2016-02-22 1.276 GiB
    SM-N750_1_20170209151401_g2ucet3tan_fac.zip
    		Download

    No matching downloads

    How to flash N750XXUDPA3

    • N750XXUDPA3 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of N750XXUDPA3 by region

    Samsung released this build in all regions (4) on the same day, February 22, 2016.

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1280 x 720 pixels
    • Display typeSAMOLED
    • RAM2 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Battery capacity3100 mAh
    • Weight162.5 g

    Specifications of SM-N7505, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    N750XXUDPA3 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy Note3 Neo, released for 4 countries, 4 CSC codes. Samsung built it on 2016-01-27.

    Yes. N750XXUDPA3 is the newest build for SM-N750 on SamFirm. The previous build was N750XXUDPA2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note3 Neo must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note3 Neo running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 25 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note3 Neo

    No changelog details available.
    Model firmware by region