Samsung Galaxy Note3 N9005VJSGBRH2
SM-N9005 1 country Android 5.0 (Lollipop)

Samsung Galaxy Note3 N9005VJSGBRH2 Firmware

Samsung Galaxy Note3 N9005VJSGBRH2 is an Android 5.0 (Lollipop) firmware for Colombia (COM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N9005VJSGBRH1: Android updated from Android 5.0 (Jelly) to Android 5.0 (Lollipop). A newer build for SM-N9005 is available: N9005ZSUGPJ2.

Download firmware
9.3/10 (478)4,310 times
Android 5.0 (Lollipop)
OS Version
2018-09-27
Build Date
1
Countries
1
CSC codes
G (16)
Bootloader binary

Bootloader binary G (16). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note3 use bootloader binary U (30) (latest: N9005ZSUGPJ2). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: N9005VJUGBPB1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-N9005
    COM Colombia
    		N9005UWAGBRH1 2018-09-27 1.226 GiB
    SM-N9005_1_20180927162652_ihgq49236o_fac.zip
    		Download

    No matching downloads

    How to flash N9005VJSGBRH2

    • N9005VJSGBRH2 has bootloader binary G (16). Your device must run binary G (16) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 4.3
    • Display diagonal14.5 cm (5.7")
    • Display resolution1920 x 1080 pixels
    • Display typeSAMOLED
    • Processor frequency2.3 GHz
    • RAM3 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity3200 mAh
    • Weight168 g

    Frequently Asked Questions

    N9005VJSGBRH2 is Android 5.0 (Lollipop) firmware for Samsung Galaxy Note3, released for Colombia (COM). Samsung built it on 2018-09-27.

    No. A newer build for SM-N9005 is available: N9005ZSUGPJ2. Install it instead of N9005VJSGBRH2 unless you need this exact version. The previous build was N9005VJSGBRH1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.226 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note3 must be on bootloader binary G (16) or lower.

    This build uses bootloader binary G (16). It can be flashed on a Samsung Galaxy Note3 running binary G (16) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 64 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note3

    No changelog details available.
    Model firmware by region