Samsung Galaxy Note3 N900TUVSFPH3
SM-N900T 1 country Android 5.0 (Lollipop)

Samsung Galaxy Note3 N900TUVSFPH3 Firmware

Samsung Galaxy Note3 N900TUVSFPH3 is an Android 5.0 (Lollipop) firmware for United States (TMB). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. A newer build for SM-N900T is available: N900TUVUFQD2.

Download firmware
9.2/10 (459)8,865 times
Android 5.0 (Lollipop)
OS Version
2016-08-26
Build Date
1
Countries
1
CSC codes
S (28)
Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note3 use bootloader binary U (30) (latest: N900TUVUFQD2). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: N900TUVSFPH3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-N900T
    TMB United States
    		N900TFPH3 — — — Download
    SM-N900T
    TMB United States
    		N900TTMBFPH3 2016-10-06 1.416 GiB
    SM-N900T_1_20170502172452_qtf32thfx0_fac.zip
    		Download

    No matching downloads

    How to flash N900TUVSFPH3

    • N900TUVSFPH3 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal14.5 cm (5.7")
    • Display resolution1920 x 1080 pixels
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3200 mAh
    • Weight168 g

    Specifications of SM-N900, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    N900TUVSFPH3 is Android 5.0 (Lollipop) firmware for Samsung Galaxy Note3, released for United States (TMB). Samsung built it on 2016-08-26.

    No. A newer build for SM-N900T is available: N900TUVUFQD2. Install it instead of N900TUVSFPH3 unless you need this exact version.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.416 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note3 must be on bootloader binary S (28) or lower.

    This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Note3 running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note3

    No changelog details available.
    Model firmware by region