Samsung Galaxy Note3 N900XXSEBPL3
SM-N900 4 countries Android 5.0 (Jelly)

Samsung Galaxy Note3 N900XXSEBPL3 Firmware

Samsung Galaxy Note3 N900XXSEBPL3 is an Android 5.0 (Jelly) firmware for 4 countries, 5 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N900XXSEBPL1: Android updated from Android 5.0 (Lollipop) to Android 5.0 (Jelly). A newer build for SM-N900 is available: N900XXUEOB1.

Download firmware
9.2/10 (456)25,617 times
Android 5.0 (Jelly)
OS Version
2016-12-22
First release
other regions until 2017-03-02
4
Countries
5
CSC codes
E (14)
Bootloader binary

Bootloader binary E (14). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note3 use bootloader binary U (30) (latest: N900XXUEOB1). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-N900
    INS, INU India
    NPL Nepal
    SLK Sri Lanka
    TML
    		N900ODDEBPF1N900DDUEBPF1 2017-03-02 2017-03-03 1.245 GiB
    SM-N900_1_20170302165239_80bmgmg9u3_fac.zip
    SM-N900
    TML
    		N900ODDEBPF1N900XXSEBPL3 2016-12-22 — — —

    No matching downloads

    How to flash N900XXSEBPL3

    • N900XXSEBPL3 has bootloader binary E (14). Your device must run binary E (14) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of N900XXSEBPL3 by region

    Samsung released this build in all regions (5) on the same day, March 3, 2017.

    Device specifications

    • Display diagonal14.5 cm (5.7")
    • Display resolution1920 x 1080 pixels
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity3200 mAh
    • Weight168 g

    Frequently Asked Questions

    N900XXSEBPL3 is Android 5.0 (Jelly) firmware for Samsung Galaxy Note3, released for 4 countries, 5 CSC codes. Samsung built it on 2016-12-22.

    No. A newer build for SM-N900 is available: N900XXUEOB1. Install it instead of N900XXSEBPL3 unless you need this exact version. The previous build was N900XXSEBPL1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.245 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note3 must be on bootloader binary E (14) or lower.

    This build uses bootloader binary E (14). It can be flashed on a Samsung Galaxy Note3 running binary E (14) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 51 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note3

    No changelog details available.
    Model firmware by region