Samsung Galaxy Note4 N9100ZHS1CPF1
SM-N9100 1 country Android 5.1.1 (Marshmallow)

Samsung Galaxy Note4 N9100ZHS1CPF1 Firmware

Samsung Galaxy Note4 N9100ZHS1CPF1 is an Android 5.1.1 (Marshmallow) firmware for Hong Kong SAR China (TGY). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N9100ZCS1CPE1: Android updated from Android 5.1.1 (KitKat) to Android 5.1.1 (Marshmallow). A newer build for SM-N9100 is available: N9100ZHU1DQH2.

Download firmware
9.1/10 (460)4,233 times
Android 5.1.1 (Marshmallow)
OS Version
2016-06-08
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: N9100ZHS1CPF1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-N9100
    TGY Hong Kong SAR China
    		N9100ZZH1CPF1 — — Download

    No matching downloads

    How to flash N9100ZHS1CPF1

    • N9100ZHS1CPF1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal14.5 cm (5.7")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • Processor frequency2.7 GHz
    • RAM3 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity3220 mAh
    • Weight175 g

    Frequently Asked Questions

    N9100ZHS1CPF1 is Android 5.1.1 (Marshmallow) firmware for Samsung Galaxy Note4, released for Hong Kong SAR China (TGY). Samsung built it on 2016-06-08.

    No. A newer build for SM-N9100 is available: N9100ZHU1DQH2. Install it instead of N9100ZHS1CPF1 unless you need this exact version. The previous build was N9100ZCS1CPE1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note4 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Note4 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 41 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note4

    The exact changes may differ depending on your device model, country/Region, and service provider.

    • Other bug fixes
    - Network connectivity enhancement.
    • The latest Android security patch has been applied.
    - Device security has been further enhanced.

    No changelog details available.
    Model firmware by region