Samsung Galaxy Note4 N910FXXS1DPHA
SM-N910F 3 countries Android 6.0.1 (Marshmallow)

Samsung Galaxy Note4 N910FXXS1DPHA Firmware

Samsung Galaxy Note4 N910FXXS1DPHA is an Android 6.0.1 (Marshmallow) firmware for Austria (DRE), Ireland (3IE), Sweden (HTS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N910FXXS1DPH9, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-N910F is available: N910FXXS1PPF1.

Download firmware
9.0/10 (450)13,208 times
Android 6.0.1 (Marshmallow)
OS Version
2016-08-10
Build Date
n/a
Security patch
3
Countries
3
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: N910FXXS1DPHA
    ModelRegionCSC VersionSizeFile nameDownload
    SM-N910F
    3IE Ireland
    		N910F1DPC1 — —
    SM-N910F
    DRE Austria
    		N910F1DPD1 — —
    SM-N910F
    HTS Sweden
    		N910F1DPC1 — —

    No matching downloads

    How to flash N910FXXS1DPHA

    • N910FXXS1DPHA has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 4.4
    • Display diagonal14.5 cm (5.7")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • Processor frequency2.7 GHz
    • RAM3 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity3220 mAh
    • Weight176 g

    Frequently Asked Questions

    N910FXXS1DPHA is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy Note4, released for Austria (DRE), Ireland (3IE), Sweden (HTS). Samsung built it on 2016-08-10.

    No. A newer build for SM-N910F is available: N910FXXS1PPF1. Install it instead of N910FXXS1DPHA unless you need this exact version. The previous build was N910FXXS1DPH9.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note4 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Note4 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 144 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note4

    No changelog details available.
    Model firmware by region