Samsung Galaxy Note4 N910T3UVU1DOK2
SM-N910T3 1 country Android 5.1.1 (Marshmallow)

Samsung Galaxy Note4 N910T3UVU1DOK2 Firmware

Samsung Galaxy Note4 N910T3UVU1DOK2 is an Android 5.1.1 (Marshmallow) firmware for United States (TMB). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N910T3UVU1DOG1: Android updated from Android 5.1.1 (Lollipop) to Android 5.1.1 (Marshmallow). A newer build for SM-N910T3 is available: N910T3UVU3EQI2.

Download firmware
9.4/10 (458)8,789 times
Android 5.1.1 (Marshmallow)
OS Version
2015-11-09
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note4 use bootloader binary 3 (latest: N910T3UVU3EQI2). If your device already runs binary 3, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: N910T3UVU1DOK2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-N910T3
    TMB United States
    		N910T31DOK2 — — — Download
    SM-N910T3
    TMB United States
    		N910T3TMB1DOK2 2015-11-30 2.398 GiB
    SM-N910T3_1_20201102173933_33tmu0y336_fac.zip
    MD5:58b9ca85290775cd8719273292672383
    SHA1:bbcd9b131f87f1fd484d61a1660282a07d365f79
    		Download

    No matching downloads

    How to flash N910T3UVU1DOK2

    • N910T3UVU1DOK2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal14.5 cm (5.7")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM3 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • Battery capacity3220 mAh
    • Weight175 g

    Specifications of SM-N9100, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    N910T3UVU1DOK2 is Android 5.1.1 (Marshmallow) firmware for Samsung Galaxy Note4, released for United States (TMB). Samsung built it on 2015-11-09.

    No. A newer build for SM-N910T3 is available: N910T3UVU3EQI2. Install it instead of N910T3UVU1DOK2 unless you need this exact version. The previous build was N910T3UVU1DOG1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.398 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note4 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Note4 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note4

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region