SM-N915P 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy Note Edge N915PVPU4COG1 Firmware

Name: Samsung Galaxy Note Edge (SM-N915P)
Brand: Samsung
Availability: InStock

Samsung Galaxy Note Edge N915PVPU4COG1 is an Android 5.1.1 (Lollipop) firmware for United States (SPR, XAS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N915PVPU4COFE, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-N915P is available: N915PVPU5DQI5.

9.1/10 (451)8,666 times

Android 5.1.1 (Lollipop)

OS Version

2015-07-29

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 4. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note Edge use bootloader binary 5 (latest: N915PVPU5DQI5). If your device already runs binary 5, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: N915PVPU4COG1

Model	Region	CSC Version	Release date	Size	File name	Download
SM-N915P	SPR, XAS United States	N915PSPT4COG1	2015-08-12	2.212 GiB	SM-N915P_1_20171025151840_z06exxf5fg_fac.zip

Device specifications

Display diagonal14.2 cm (5.6")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
RAM3 GB
Rear camera resolution16 MP
Rear camera typeSingle camera
Battery capacity3000 mAh
Weight174 g

Specifications of SM-N915F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash N915PVPU4COG1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

N915PVPU4COG1 has bootloader binary 4. Your device must run binary 4 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

N915PVPU4COG1 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy Note Edge, released for United States (SPR, XAS). Samsung built it on 2015-07-29.

No. A newer build for SM-N915P is available: N915PVPU5DQI5. Install it instead of N915PVPU4COG1 unless you need this exact version. The previous build was N915PVPU4COFE.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.212 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note Edge must be on bootloader binary 4 or lower.

This build uses bootloader binary 4. It can be flashed on a Samsung Galaxy Note Edge running binary 4 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 18 other builds of this model use the same binary, so you can switch between them in both directions.