Samsung Galaxy Note10+ N975FXXU4CTF2
SM-N975F 3 countries Android 10

Samsung Galaxy Note10+ N975FXXU4CTF2 Firmware

Samsung Galaxy Note10+ N975FXXU4CTF2 is an Android 10 firmware for Chile (CRC), Guatemala (PGU), Panama (CPA). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N975FXXU4CTE9, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-N975F is available: N975FXXU9HXJE.

OS updates guaranteed until: Android 12Security updates until: Aug 1, 2023
Download firmware
8.9/10 (484)12,931 times
Android 10
OS Version
2020-06-12
Build Date
3
Countries
3
CSC codes
4
Bootloader binary

Bootloader binary 4. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note10+ use bootloader binary 9 (latest: N975FXXU9HXJE). If your device already runs binary 9, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: N975FXXU4CTE9
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-N975F
    CPA Panama
    CRC Chile
    PGU Guatemala
    		N975FOWA4CTF2 2020-06-25 5.146 GiB
    SM-N975F_1_20201204003433_ktypjqj59s_fac.zip
    MD5:1222d31a3cb2851994da27ab1f646fd6
    SHA1:970a7493b65d52e94ebbc144af234de8138e5489
    		Download

    No matching downloads

    How to flash N975FXXU4CTF2

    • N975FXXU4CTF2 has bootloader binary 4. Your device must run binary 4 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of N975FXXU4CTF2 by region

    Samsung released this build in all regions (3) on the same day, June 25, 2020.

    Device specifications

    • Launched withAndroid 9.0
    • Display diagonal17.3 cm (6.8")
    • Display resolution3040 x 1440 pixels
    • Display typeDynamic AMOLED
    • Processor frequency2.7 GHz
    • RAM12 GB
    • Rear camera resolution12 MP
    • Rear camera typeQuad camera
    • SIM cardsHybrid dual SIM
    • Battery capacity4300 mAh
    • Weight196 g

    Frequently Asked Questions

    N975FXXU4CTF2 is Android 10 firmware for Samsung Galaxy Note10+, released for Chile (CRC), Guatemala (PGU), Panama (CPA). Samsung built it on 2020-06-12.

    No. A newer build for SM-N975F is available: N975FXXU9HXJE. Install it instead of N975FXXU4CTF2 unless you need this exact version. The previous build was N975FXXU4CTE9.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 5.146 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note10+ must be on bootloader binary 4 or lower.

    This build uses bootloader binary 4. It can be flashed on a Samsung Galaxy Note10+ running binary 4 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note10+

    No changelog details available.
    Model firmware by region