Samsung Galaxy Tab (3G + WiFi) (Latin) P1000LVIJR2
GT-P1000L 1 country Android 2.3.6 (Gingerbread)

Samsung Galaxy Tab (3G + WiFi) (Latin) P1000LVIJR2 Firmware

Samsung Galaxy Tab (3G + WiFi) (Latin) P1000LVIJR2 is an Android 2.3.6 (Gingerbread) firmware for Brazil (ZTM, ZVV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P1000LUTJP8: Android updated from Android 2.3.3 (Gingerbread) to Android 2.3.6 (Gingerbread); bootloader binary raised from U (30) to V (31), so after installing it there is no way back to older builds. A newer build for GT-P1000L is available: P1000LVJJME.

8.8/10 (472)8,483 times
Android 2.3.6 (Gingerbread)
OS Version
2011-11-30
Build Date
n/a
Security patch
1
Countries
2
CSC codes
V (31)
Bootloader binary

Bootloader binary V (31). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionSizeFile nameDownload
    GT-P1000L
    ZTM Brazil
    		P1000LZTMJR3P1000LZTMJR3 — —
    GT-P1000L
    ZVV Brazil
    		P1000LZVVJR3P1000LZVVJR3 — —

    No matching downloads

    How to flash P1000LVIJR2

    • P1000LVIJR2 has bootloader binary V (31). Your device must run binary V (31) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    P1000LVIJR2 is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy Tab (3G + WiFi) (Latin), released for Brazil (ZTM, ZVV). Samsung built it on 2011-11-30.

    No. A newer build for GT-P1000L is available: P1000LVJJME. Install it instead of P1000LVIJR2 unless you need this exact version. The previous build was P1000LUTJP8.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab (3G + WiFi) (Latin) must be on bootloader binary V (31) or lower.

    This build uses bootloader binary V (31). It can be flashed on a Samsung Galaxy Tab (3G + WiFi) (Latin) running binary V (31) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab (3G + WiFi) (Latin)

    No changelog details available.
    No changelog details available.
    No changelog details available.
    Model firmware by region