Samsung GALAXY Tab 7.0 P1010UJKB4
GT-P1010 1 country Android 2.2.1 (Froyo)

Samsung GALAXY Tab 7.0 P1010UJKB4 Firmware

Samsung GALAXY Tab 7.0 P1010UJKB4 is an Android 2.2.1 (Froyo) firmware for Mexico (TCE). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P1010DXKP5: Android updated from Android 2.3.6 (Gingerbread) to Android 2.2.1 (Froyo); bootloader binary raised from D (13) to U (30), so after installing it there is no way back to older builds. A newer build for GT-P1010 is available: P1010ZTLE7.

9.2/10 (471)4,438 times
Android 2.2.1 (Froyo)
OS Version
2011-02-28
Build Date
n/a
Security patch
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung GALAXY Tab 7.0 use bootloader binary Z (35) (latest: P1010ZTLE7). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: P1010UJKB4
    ModelRegionCSC VersionSizeFile nameDownload
    GT-P1010
    TCE Mexico
    		P1010UVSKB4 — —

    No matching downloads

    How to flash P1010UJKB4

    • P1010UJKB4 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    P1010UJKB4 is Android 2.2.1 (Froyo) firmware for Samsung GALAXY Tab 7.0, released for Mexico (TCE). Samsung built it on 2011-02-28.

    No. A newer build for GT-P1010 is available: P1010ZTLE7. Install it instead of P1010UJKB4 unless you need this exact version. The previous build was P1010DXKP5.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung GALAXY Tab 7.0 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung GALAXY Tab 7.0 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary U (30).

    Other builds and changelog for Samsung GALAXY Tab 7.0

    No changelog details available.
    No changelog details available.
    No changelog details available.
    No changelog details available.
    Model firmware by region