SM-P605 2 countries Android 4.4.2 (KitKat)

Samsung Galaxy Note 10.1 2014 Edition P605ZSSCQC1 Firmware

Name: Samsung Galaxy Note 10.1 2014 Edition (SM-P605)
Brand: Samsung
Availability: InStock

Samsung Galaxy Note 10.1 2014 Edition P605ZSSCQC1 is an Android 4.4.2 (KitKat) firmware for Hong Kong SAR China (TGY), Taiwan (BRI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P605XXS1ERK1 https://samfirm.shop/build/P605XXS1ERK1: Android updated from Android 5.1.1 (Lollipop) to Android 4.4.2 (KitKat); bootloader binary raised from 1 to S (28), so after installing it there is no way back to older builds. A newer build for SM-P605 is available: P605XXUDOE2 https://samfirm.shop/build/P605XXUDOE2.

8.9/10 (471)9,009 times

Android 4.4.2 (KitKat)

OS Version

2017-04-20

First release

other regions until 2017-04-27

n/a

Security patch

Countries

CSC codes

S (28)

Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note 10.1 2014 Edition use bootloader binary U (30) (latest: P605XXUDOE2). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: P605ZSSCQC1

Model	Region	CSC Version	Release date	Size	File name	Download
SM-P605	BRI Taiwan TGY Hong Kong SAR China	P605OZSCQC1	2017-04-20	1.484 GiB	SM-P605_1_20170419141813_80fc2uazfx_fac.zip

Device specifications

Launched withAndroid
Display diagonal25.6 cm (10.1")
Display resolution2560 x 1600 pixels
Processor frequency2.3 GHz
Rear camera resolution8 MP
Rear camera typeSingle camera
Front camera resolution2 MP
Wi-Fi standardWi-Fi 5 (802.11ac)
Weight547 g

How to flash P605ZSSCQC1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

P605ZSSCQC1 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

P605ZSSCQC1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note 10.1 2014 Edition, released for Hong Kong SAR China (TGY), Taiwan (BRI). Samsung built it on 2017-04-20.

No. A newer build for SM-P605 is available: P605XXUDOE2. Install it instead of P605ZSSCQC1 unless you need this exact version. The previous build was P605XXS1ERK1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.484 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note 10.1 2014 Edition must be on bootloader binary S (28) or lower.

This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Note 10.1 2014 Edition running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.