Samsung Galaxy Note 10.1 2014 Edition P605ZSUCNI1
SM-P605 2 countries Android 4.4.2 (KitKat)

Samsung Galaxy Note 10.1 2014 Edition P605ZSUCNI1 Firmware

Samsung Galaxy Note 10.1 2014 Edition P605ZSUCNI1 is an Android 4.4.2 (KitKat) firmware for Hong Kong SAR China (TGY), Taiwan (BRI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P605XXUCNG1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-P605 is available: P605XXUDOE2.

Download firmware
8.9/10 (460)8,879 times
Android 4.4.2 (KitKat)
OS Version
2014-09-22
Build Date
2
Countries
2
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: P605ZSUCNI1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-P605
    BRI Taiwan
    		P605OZSCNI1 — — Download
    SM-P605
    TGY Hong Kong SAR China
    		P605OZSCNI1 — — Download

    No matching downloads

    How to flash P605ZSUCNI1

    • P605ZSUCNI1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal25.6 cm (10.1")
    • Display resolution2560 x 1600 pixels
    • Processor frequency2.3 GHz
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Front camera resolution2 MP
    • Wi-Fi standardWi-Fi 5 (802.11ac)
    • Weight547 g

    Frequently Asked Questions

    P605ZSUCNI1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note 10.1 2014 Edition, released for Hong Kong SAR China (TGY), Taiwan (BRI). Samsung built it on 2014-09-22.

    No. A newer build for SM-P605 is available: P605XXUDOE2. Install it instead of P605ZSUCNI1 unless you need this exact version. The previous build was P605XXUCNG1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note 10.1 2014 Edition must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note 10.1 2014 Edition running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 22 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note 10.1 2014 Edition

    No changelog details available.
    Model firmware by region