GT-P6200L 2 countries Android 3.2 (Honeycomb)

Samsung Galaxy Tab 7.0 Plus P6200LUBMF1 Firmware

Name: Samsung Galaxy Tab 7.0 Plus (GT-P6200L)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab 7.0 Plus P6200LUBMF1 is an Android 3.2 (Honeycomb) firmware for Colombia (COO), Panama (TPA). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P6200LUBLB3 https://samfirm.shop/build/P6200LUBLB3, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-P6200L is available: P6200LVSMH1 https://samfirm.shop/build/P6200LVSMH1.

8.9/10 (471)8,604 times

Android 3.2 (Honeycomb)

OS Version

2013-05-29

First release

other regions until 2013-07-06

n/a

Security patch

Countries

CSC codes

U (30)

Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab 7.0 Plus use bootloader binary V (31) (latest: P6200LVSMH1). If your device already runs binary V (31), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: P6200LUBMD2

Model	Region	CSC Version	Build Date	Release date	Size	File name	Download
GT-P6200L	COO Colombia	P6200LCOOMF1	2013-07-06	2013-07-10	—	—
GT-P6200L	TPA Panama	P6200LUWHMF1	2013-05-29	2013-07-08	—	—

How to flash P6200LUBMF1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

P6200LUBMF1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

P6200LUBMF1 is Android 3.2 (Honeycomb) firmware for Samsung Galaxy Tab 7.0 Plus, released for Colombia (COO), Panama (TPA). Samsung built it on 2013-05-29.

No. A newer build for GT-P6200L is available: P6200LVSMH1. Install it instead of P6200LUBMF1 unless you need this exact version. The previous build was P6200LUBLB3.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab 7.0 Plus must be on bootloader binary U (30) or lower.

This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Tab 7.0 Plus running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 4 other builds of this model use the same binary, so you can switch between them in both directions.