Samsung Galaxy Note Pro P900XXS0BPL3
SM-P900 1 country Android 5.0.2 (Lollipop)

Samsung Galaxy Note Pro P900XXS0BPL3 Firmware

Samsung Galaxy Note Pro P900XXS0BPL3 is an Android 5.0.2 (Lollipop) firmware for Switzerland (AUT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P900XXS0BPL2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-P900 is available: P900KXUBPK3.

Download firmware
8.9/10 (456)8,674 times
Android 5.0.2 (Lollipop)
OS Version
2016-12-02
Build Date
1
Countries
1
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note Pro use bootloader binary U (30) (latest: P900KXUBPK3). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: P900XXS0BPL3
    ModelRegionCSC VersionSizeFile nameDownload
    SM-P900
    AUT Switzerland
    		P9000BOF1 — —
    SM-P900
    AUT Switzerland
    		P900AUT0BOF1 — —

    No matching downloads

    How to flash P900XXS0BPL3

    • P900XXS0BPL3 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal31 cm (12.2")
    • Display resolution2560 x 1600 pixels
    • Processor frequency1.9 GHz
    • Processor familySamsung Exynos
    • Processor model5 Octa
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Front camera resolution2 MP
    • Wi-Fi standardWi-Fi 5 (802.11ac)
    • Weight732 g

    Frequently Asked Questions

    P900XXS0BPL3 is Android 5.0.2 (Lollipop) firmware for Samsung Galaxy Note Pro, released for Switzerland (AUT). Samsung built it on 2016-12-02.

    No. A newer build for SM-P900 is available: P900KXUBPK3. Install it instead of P900XXS0BPL3 unless you need this exact version. The previous build was P900XXS0BPL2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note Pro must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Note Pro running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 16 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note Pro

    No changelog details available.
    Model firmware by region