Samsung Galaxy Note Pro 12.2 P901ZCUANB3
SM-P901 1 country Android 4.4.2 (KitKat)

Samsung Galaxy Note Pro 12.2 P901ZCUANB3 Firmware

Samsung Galaxy Note Pro 12.2 P901ZCUANB3 is an Android 4.4.2 (KitKat) firmware for China (CHN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P901XXUANB1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-P901 is available: P901UBUAOC1.

8.7/10 (472)4,308 times
Android 4.4.2 (KitKat)
OS Version
2014-02-11
Build Date
n/a
Security patch
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: P901ZCUANB3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-P901
    CHN China
    		P901CHNANB3 2014-03-05 1.373 GiB
    SM-P901_1_20170713055127_6cb5wfnzv4_fac.zip

    No matching downloads

    How to flash P901ZCUANB3

    • P901ZCUANB3 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    P901ZCUANB3 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note Pro 12.2, released for China (CHN). Samsung built it on 2014-02-11.

    No. A newer build for SM-P901 is available: P901UBUAOC1. Install it instead of P901ZCUANB3 unless you need this exact version. The previous build was P901XXUANB1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.373 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note Pro 12.2 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note Pro 12.2 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note Pro 12.2

    No changelog details available.

    Improved stability.

    No changelog details available.

    - The latest Android security patch has been applied.
    ㆍDevice security has been further enhanced.

    No changelog details available.
    Model firmware by region