Samsung Galaxy Note Pro 12.2 P901XXSAQD1
SM-P901 3 countries Android 4.4.2 (KitKat)

Samsung Galaxy Note Pro 12.2 P901XXSAQD1 Firmware

Samsung Galaxy Note Pro 12.2 P901XXSAQD1 is an Android 4.4.2 (KitKat) firmware for Cambodia (CAM), Indonesia (XSE), Vietnam (XXV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P901XXS0BQE1: Android updated from Android 5.0.2 (Lollipop) to Android 4.4.2 (KitKat); bootloader binary raised from 0 to S (28), so after installing it there is no way back to older builds. A newer build for SM-P901 is available: P901UBUAOC1.

Download firmware
9.3/10 (457)12,880 times
Android 4.4.2 (KitKat)
OS Version
3
Countries
3
CSC codes
S (28)
Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note Pro 12.2 use bootloader binary U (30) (latest: P901UBUAOC1). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: P901XXUANB5
    ModelRegionCSC VersionSizeFile nameDownload
    SM-P901
    CAM Cambodia
    		P901OLBANA9 — — Download
    SM-P901
    XSE Indonesia
    		P901OLBANA9 — — Download
    SM-P901
    XXV Vietnam
    		P901OLBANA9 — — Download

    No matching downloads

    How to flash P901XXSAQD1

    • P901XXSAQD1 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    P901XXSAQD1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note Pro 12.2, released for Cambodia (CAM), Indonesia (XSE), Vietnam (XXV).

    No. A newer build for SM-P901 is available: P901UBUAOC1. Install it instead of P901XXSAQD1 unless you need this exact version. The previous build was P901XXS0BQE1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note Pro 12.2 must be on bootloader binary S (28) or lower.

    This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Note Pro 12.2 running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note Pro 12.2

    No changelog details available.

    Improved stability.

    No changelog details available.

    - The latest Android security patch has been applied.
    ㆍDevice security has been further enhanced.

    No changelog details available.
    Model firmware by region