SM-R765F 1 country

Samsung Gear S3 Frontier R765FXXU2FTD4 Firmware

Samsung Gear S3 Frontier R765FXXU2FTD4 is an Android firmware for Singapore (XSP). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build R765FXXU2ESF2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-R765F is available: R765FXXU2FUD1.

Download firmware
9.0/10 (35)112 times
2020-06-02
Build Date
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: R765FXXU2FTD4
    ModelRegionCSC VersionSizeFile nameDownload
    SM-R765F
    XSP Singapore
    		R765FOLB2FTD4 674.227 MiB
    SM-R765F_1_20200602181018_wvzbb7rikt_fac.zip
    		Download

    No matching downloads

    How to flash R765FXXU2FTD4

    • R765FXXU2FTD4 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    No. A newer build for SM-R765F is available: R765FXXU2FUD1. Install it instead of R765FXXU2FTD4 unless you need this exact version. The previous build was R765FXXU2ESF2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 674.227 MiB; keep about twice that free on the computer to unzip it. The Samsung Gear S3 Frontier must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Gear S3 Frontier running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Gear S3 Frontier

    No changelog details available.

    - One UI for Watch
    · Check information on your watch at a quick glance. Updated graphics(motion, interface) delivers refreshed look
    - Watch faces
    · You can now download new designs of watch faces
    - Quick panel
    · Now supports additional pages to allow quick access to setting control
    - Settings
    · Setting menus have been updated for easier discovery. Daily briefing setting has been added for watch to be smarter. Additionally, Sleeping mode can now be turned on/off. Watch can now be set to wake...

    No changelog details available.
    Model firmware by region