GT-S5360 1 country Android 2.3.6 (Gingerbread)

Samsung Galaxy y S5360XLMJ2 Firmware

Name: Samsung Galaxy y (GT-S5360)
Brand: Samsung
Availability: InStock

Samsung Galaxy y S5360XLMJ2 is an Android 2.3.6 (Gingerbread) firmware for Russia (SER). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S5360XLMD1 https://samfirm.shop/build/S5360XLMD1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-S5360 is available: S5360ZHLG1 https://samfirm.shop/build/S5360ZHLG1.

9.1/10 (23)248 times

Android 2.3.6 (Gingerbread)

OS Version

2015-01-24

Build Date

n/a

Security patch

Countries

CSC codes

X (33)

Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy y use bootloader binary Z (35) (latest: S5360ZHLG1). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: S5360XXMK1

Model	Region	CSC Version	Release date	Size	File name	Download
GT-S5360	SER Russia	S5360SERMI1	2013-12-12	135.713 MiB	GT-S5360_SER_12_20150124142900_6z2oxb4xq5_fac.zip

Device specifications

Launched withAndroid 2.3
Display diagonal7.62 cm (3")
Display resolution320 x 240 pixels
Display typeTFT
Processor frequency0.832 GHz
Rear camera resolution2 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity120 mAh
Weight97.5 g

How to flash S5360XLMJ2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

S5360XLMJ2 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

S5360XLMJ2 is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy y, released for Russia (SER). Samsung built it on 2015-01-24.

No. A newer build for GT-S5360 is available: S5360ZHLG1. Install it instead of S5360XLMJ2 unless you need this exact version. The previous build was S5360XLMD1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 135.713 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy y must be on bootloader binary X (33) or lower.

This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy y running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 12 other builds of this model use the same binary, so you can switch between them in both directions.