Samsung Galaxy y S5360ZHLG1
GT-S5360 1 country Android 2.3.6 (Gingerbread)

Samsung Galaxy y S5360ZHLG1 Firmware

Samsung Galaxy y S5360ZHLG1 is an Android 2.3.6 (Gingerbread) firmware for Hong Kong SAR China (TGY). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S5360XXMK1: bootloader binary raised from X (33) to Z (35), so after installing it there is no way back to older builds. This is the newest build for GT-S5360.

Download firmware
9.0/10 (489)3,156 times
Android 2.3.6 (Gingerbread)
OS Version
2012-07-25
Build Date
1
Countries
1
CSC codes
Z (35)
Bootloader binary

Bootloader binary Z (35). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: S5360XXLF3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    GT-S5360
    TGY Hong Kong SAR China
    		S5360ZZHLG1 2012-08-07 125.467 MiB
    GT-S5360_TGY_1_20120725150816_sfxns6icqg.zip
    		Download

    No matching downloads

    How to flash S5360ZHLG1

    • S5360ZHLG1 has bootloader binary Z (35). Your device must run binary Z (35) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 2.3
    • Display diagonal7.62 cm (3")
    • Display resolution320 x 240 pixels
    • Display typeTFT
    • Processor frequency0.832 GHz
    • Rear camera resolution2 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity120 mAh
    • Weight97.5 g

    Frequently Asked Questions

    S5360ZHLG1 is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy y, released for Hong Kong SAR China (TGY). Samsung built it on 2012-07-25.

    Yes. S5360ZHLG1 is the newest build for GT-S5360 on SamFirm. The previous build was S5360XXMK1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 125.467 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy y must be on bootloader binary Z (35) or lower.

    This build uses bootloader binary Z (35). It can be flashed on a Samsung Galaxy y running binary Z (35) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary Z (35).

    Other builds and changelog for Samsung Galaxy y

    No changelog details available.
    Model firmware by region