Samsung GALAXY Fit S5670XWKQ2
GT-S5670 1 country Android 2.3.4 (Gingerbread)

Samsung GALAXY Fit S5670XWKQ2 Firmware

Samsung GALAXY Fit S5670XWKQ2 is an Android 2.3.4 (Gingerbread) firmware for Poland (XEO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S5670DXKT7: Android updated from Android 2.3.6 (Gingerbread) to Android 2.3.4 (Gingerbread); bootloader binary raised from D (13) to X (33), so after installing it there is no way back to older builds. A newer build for GT-S5670 is available: S5670ZCKPA.

Download firmware
9.0/10 (476)4,326 times
Android 2.3.4 (Gingerbread)
OS Version
2011-06-29
Build Date
1
Countries
1
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung GALAXY Fit use bootloader binary Z (35) (latest: S5670ZCKPA). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: S5670OXXKQ2
    ModelRegionCSC VersionSizeFile nameDownload
    GT-S5670
    XEO Poland
    		S5670XWKQ2 — —

    No matching downloads

    How to flash S5670XWKQ2

    • S5670XWKQ2 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 2.2
    • Display diagonal8.13 cm (3.2")
    • Display resolution240 x 320 pixels
    • Display typeTFT
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity1350 mAh
    • Weight108.2 g

    Frequently Asked Questions

    S5670XWKQ2 is Android 2.3.4 (Gingerbread) firmware for Samsung GALAXY Fit, released for Poland (XEO). Samsung built it on 2011-06-29.

    No. A newer build for GT-S5670 is available: S5670ZCKPA. Install it instead of S5670XWKQ2 unless you need this exact version. The previous build was S5670DXKT7.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung GALAXY Fit must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung GALAXY Fit running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung GALAXY Fit

    No changelog details available.
    Model firmware by region