GT-S6102 3 countries Android 2.3.6 (Gingerbread)

Samsung Galaxy Y Duos S6102XXLL1 Firmware

Name: Samsung Galaxy Y Duos (GT-S6102)
Brand: Samsung
Availability: InStock

Samsung Galaxy Y Duos S6102XXLL1 is an Android 2.3.6 (Gingerbread) firmware for Australia (XSA), South Africa (XFA, XFE), XFC. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S6102XXLH5 https://samfirm.shop/build/S6102XXLH5, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-S6102 is available: S6102ZSLH2 https://samfirm.shop/build/S6102ZSLH2.

9.1/10 (471)17,311 times

Android 2.3.6 (Gingerbread)

OS Version

2012-12-03

Build Date

n/a

Security patch

Countries

CSC codes

X (33)

Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Y Duos use bootloader binary Z (35) (latest: S6102ZSLH2). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: S6102XXLL1

Model	Region	CSC Version	Build Date	Release date	Size	File name
GT-S6102	XFA South Africa	S610OJCLF1	—	—	—	—
GT-S6102	XFC	S610OJCLF1	—	—	—	—
GT-S6102	XFE South Africa	S610OJCLF1	—	—	—	—
GT-S6102	XSA Australia	S6102XSALJ1	2012-12-03	2013-01-08	—	—

Device specifications

Launched withAndroid 2.3
Display diagonal7.98 cm (3.14")
Display resolution240 x 320 pixels
Display typeTFT
Processor frequency0.832 GHz
Rear camera resolution3 MP
Rear camera typeSingle camera
SIM cardsDual SIM
Battery capacity1300 mAh
Weight109 g

How to flash S6102XXLL1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

S6102XXLL1 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

S6102XXLL1 is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy Y Duos, released for Australia (XSA), South Africa (XFA, XFE), XFC. Samsung built it on 2012-12-03.

No. A newer build for GT-S6102 is available: S6102ZSLH2. Install it instead of S6102XXLL1 unless you need this exact version. The previous build was S6102XXLH5.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Y Duos must be on bootloader binary X (33) or lower.

This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Y Duos running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 11 other builds of this model use the same binary, so you can switch between them in both directions.