Samsung Galaxy Y Duos S6102XXLG3
GT-S6102 2 countries Android 2.3.6 (Gingerbread)

Samsung Galaxy Y Duos S6102XXLG3 Firmware

Samsung Galaxy Y Duos S6102XXLG3 is an Android 2.3.6 (Gingerbread) firmware for Poland (PRT), Portugal (TMN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S6102XXLC2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-S6102 is available: S6102ZSLH2.

Download firmware
8.8/10 (480)8,666 times
Android 2.3.6 (Gingerbread)
OS Version
2012-07-24
Build Date
2
Countries
2
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Y Duos use bootloader binary Z (35) (latest: S6102ZSLH2). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: S6102XXLG3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    GT-S6102
    PRT Poland
    		S6102PRTLG1 — — — Download
    GT-S6102
    TMN Portugal
    		S6102TMNLC2 2012-08-20 — — Download

    No matching downloads

    How to flash S6102XXLG3

    • S6102XXLG3 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of S6102XXLG3 by region

    Samsung released this build in all regions (1) on the same day, August 20, 2012.

    Device specifications

    • Launched withAndroid 2.3
    • Display diagonal7.98 cm (3.14")
    • Display resolution240 x 320 pixels
    • Display typeTFT
    • Processor frequency0.832 GHz
    • Rear camera resolution3 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity1300 mAh
    • Weight109 g

    Frequently Asked Questions

    S6102XXLG3 is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy Y Duos, released for Poland (PRT), Portugal (TMN). Samsung built it on 2012-07-24.

    No. A newer build for GT-S6102 is available: S6102ZSLH2. Install it instead of S6102XXLG3 unless you need this exact version. The previous build was S6102XXLC2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Y Duos must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Y Duos running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 11 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Y Duos

    No changelog details available.
    Model firmware by region