GT-S7710 3 countries Android 4.1.2

Samsung Galaxy Xcover2 S7710XXAMH3 Firmware

Name: Samsung Galaxy Xcover2 (GT-S7710)
Brand: Samsung
Availability: InStock

Samsung Galaxy Xcover2 S7710XXAMH3 is an Android 4.1.2 firmware for Czechia (TMZ), Hungary (TMH), Poland (TPL). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S7710XXAMF6 https://samfirm.shop/build/S7710XXAMF6: Android updated from Jelly(Android Bean) to Android 4.1.2. A newer build for GT-S7710 is available: S7710XXAOB2 https://samfirm.shop/build/S7710XXAOB2.

9.1/10 (471)12,960 times

Android 4.1.2

OS Version

2013-08-26

Build Date

n/a

Security patch

Countries

CSC codes

X (33)

Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: S7710XXAMH3

Model	Region	CSC Version	Size	File name
GT-S7710	TMH Hungary	S7710TMHAMI2	787.137 MiB	GT-S7710_TMH_1_20140825172940_330753tz1w_fac.zip
GT-S7710	TMZ Czechia	S7710TMZAMI2	724.754 MiB	GT-S7710_TMZ_1_20140826112010_8rurlu9a8p_fac.zip
GT-S7710	TPL Poland	S7710TPLAMI2	742.829 MiB	GT-S7710_TPL_1_20140826114440_f6jrxp0ks6_fac.zip

Device specifications

Launched withAndroid 4.1
Display diagonal10.2 cm (4")
Display resolution480 x 800 pixels
Display typeTFT
Processor frequency1 GHz
Rear camera resolution5 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity1700 mAh
Weight148 g

How to flash S7710XXAMH3

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

S7710XXAMH3 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

S7710XXAMH3 is Android 4.1.2 firmware for Samsung Galaxy Xcover2, released for Czechia (TMZ), Hungary (TMH), Poland (TPL). Samsung built it on 2013-08-26.

No. A newer build for GT-S7710 is available: S7710XXAOB2. Install it instead of S7710XXAMH3 unless you need this exact version. The previous build was S7710XXAMF6.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Xcover2 must be on bootloader binary X (33) or lower.

This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Xcover2 running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 25 other builds of this model use the same binary, so you can switch between them in both directions.