Samsung Galaxy Xcover2 S7710XXAMJ4
GT-S7710 2 countries Android 4.1.2

Samsung Galaxy Xcover2 S7710XXAMJ4 Firmware

Samsung Galaxy Xcover2 S7710XXAMJ4 is an Android 4.1.2 firmware for Cyprus (CYV), Nordic Europe (NEE). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build S7710XXAMJ2: Android updated from Jelly(Android Bean) to Android 4.1.2. A newer build for GT-S7710 is available: S7710XXAOB2.

9.0/10 (133)5,218 times
Android 4.1.2
OS Version
2013-10-08
First release
other regions until 2013-10-23
n/a
Security patch
2
Countries
2
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: S7710XXAMJ4
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    GT-S7710
    CYV Cyprus
    		S7710OXXAMJ2 2013-10-23 2013-10-23 755.587 MiB
    GT-S7710_CYV_1_20140612151330_k67060o0iv_fac.zip
    GT-S7710
    NEE Nordic Europe
    		S7710OXXAMJ2 2013-10-08 — 781.545 MiB
    GT-S7710_1_20150515201239_vgsl3pdxvv_fac.zip

    No matching downloads

    How to flash S7710XXAMJ4

    • S7710XXAMJ4 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of S7710XXAMJ4 by region

    Samsung released this build in all regions (1) on the same day, October 23, 2013.

    Device specifications

    • Launched withAndroid 4.1
    • Display diagonal10.2 cm (4")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • Processor frequency1 GHz
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity1700 mAh
    • Weight148 g

    Frequently Asked Questions

    S7710XXAMJ4 is Android 4.1.2 firmware for Samsung Galaxy Xcover2, released for Cyprus (CYV), Nordic Europe (NEE). Samsung built it on 2013-10-08.

    No. A newer build for GT-S7710 is available: S7710XXAOB2. Install it instead of S7710XXAMJ4 unless you need this exact version. The previous build was S7710XXAMJ2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Xcover2 must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Xcover2 running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 25 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Xcover2

    No changelog details available.
    Model firmware by region