Samsung Galaxy S9+ SC03KOMU1CTG1
SC-03K 1 country Android 10 (Pie)

Samsung Galaxy S9+ SC03KOMU1CTG1 Firmware

Samsung Galaxy S9+ SC03KOMU1CTG1 is an Android 10 (Pie) firmware for Japan (DCM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build SC03KOMU1CTC1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SC-03K is available: SC03KOMU1CUF3.

Download firmware
8.7/10 (456)8,704 times
Android 10 (Pie)
OS Version
2020-07-01
Build Date
n/a
Security patch
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: SC03KOMU1CTG1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SC-03K
    DCM Japan
    		SC03K1CTG1 — — —
    SC-03K
    DCM Japan
    		SC03KDCM1CTG1 2020-07-13 4.196 GiB
    SC-03K_2_20200701182403_12uzwmr6ny_fac.zip

    No matching downloads

    How to flash SC03KOMU1CTG1

    • SC03KOMU1CTG1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    SC03KOMU1CTG1 is Android 10 (Pie) firmware for Samsung Galaxy S9+, released for Japan (DCM). Samsung built it on 2020-07-01.

    No. A newer build for SC-03K is available: SC03KOMU1CUF3. Install it instead of SC03KOMU1CTG1 unless you need this exact version. The previous build was SC03KOMU1CTC1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 4.196 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S9+ must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy S9+ running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S9+

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region