Samsung Galaxy Note Edge SCL24KDU1CPI2
SCL24 1 country Android 6.0.1 (KitKat)

Samsung Galaxy Note Edge SCL24KDU1CPI2 Firmware

Samsung Galaxy Note Edge SCL24KDU1CPI2 is an Android 6.0.1 (KitKat) firmware for Japan (KDI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build SCL24KDU1CPH3, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SCL24 is available: SCL24KDU1CQG2.

Download firmware
9.2/10 (462)8,666 times
Android 6.0.1 (KitKat)
OS Version
2016-08-31
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: SCL24KDU1CPI2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SCL24
    KDI Japan
    		KDU1CPI21CPI2 — — — Download
    SCL24
    KDI Japan
    		SCL24KDI1CPI2 2016-10-18 2.483 GiB
    SCL24_1_20201109141103_p8kdt1zgoz_fac.zip
    		Download

    No matching downloads

    How to flash SCL24KDU1CPI2

    • SCL24KDU1CPI2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    SCL24KDU1CPI2 is Android 6.0.1 (KitKat) firmware for Samsung Galaxy Note Edge, released for Japan (KDI). Samsung built it on 2016-08-31.

    No. A newer build for SCL24 is available: SCL24KDU1CQG2. Install it instead of SCL24KDU1CPI2 unless you need this exact version. The previous build was SCL24KDU1CPH3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.483 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note Edge must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Note Edge running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 6 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note Edge

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region