SM-T116BU 6 countries Android 4.4.4 (KitKat)

Samsung Galaxy Tab Plus 7.0 T116BUUBU0ARC2 Firmware

Name: Samsung Galaxy Tab Plus 7.0 (SM-T116BU)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab Plus 7.0 T116BUUBU0ARC2 is an Android 4.4.4 (KitKat) firmware for 6 countries, 6 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T116BUUBU0AQK1 https://samfirm.shop/build/T116BUUBU0AQK1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-T116BU is available: T116BUUBU0ARE1 https://samfirm.shop/build/T116BUUBU0ARE1.

9.0/10 (473)26,149 times

Android 4.4.4 (KitKat)

OS Version

2018-03-05

First release

other regions until 2018-03-27

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: T116BUUBU0ARC2

Model	Region	CSC Version	Build Date	Release date	Size	File name
SM-T116BU	COO Colombia EON Trinidad & Tobago TPA Panama	T116BUUUB0ARC2	2018-03-27	2018-03-27	801.866 MiB	SM-T116BU_1_20180327111414_e8eg1o5fzo_fac.zip
SM-T116BU	CTU Uruguay	T116BUUWA0ARC2	—	—	—	—
SM-T116BU	PNT Peru	T116BUPNT0ARC2	—	—	—	—
SM-T116BU	ZTM Brazil	T116BUZTM0ARC2	—	—	—	—

Device specifications

Display diagonal17.8 cm (7")
Display resolution1024 x 600 pixels
Processor frequency1.3 GHz
Rear camera resolution2 MP
Rear camera typeSingle camera
Front camera resolution2 MP
Weight322 g

How to flash T116BUUBU0ARC2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

T116BUUBU0ARC2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

T116BUUBU0ARC2 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy Tab Plus 7.0, released for 6 countries, 6 CSC codes. Samsung built it on 2018-03-05.

No. A newer build for SM-T116BU is available: T116BUUBU0ARE1. Install it instead of T116BUUBU0ARC2 unless you need this exact version. The previous build was T116BUUBU0AQK1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 801.866 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab Plus 7.0 must be on bootloader binary 0 or lower.

This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Tab Plus 7.0 running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 19 other builds of this model use the same binary, so you can switch between them in both directions.