Samsung Galaxy Tab3 7.0 T211MVJANK1
SM-T211M 1 country Android 4.1.2 (KitKat)

Samsung Galaxy Tab3 7.0 T211MVJANK1 Firmware

Samsung Galaxy Tab3 7.0 T211MVJANK1 is an Android 4.1.2 (KitKat) firmware for Brazil (ZTM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T211MVJANC1: Android updated from Jelly(Android Bean) to Android 4.1.2 (KitKat). A newer build for SM-T211M is available: T211MVJUBOB1.

Download firmware
8.9/10 (461)4,263 times
Android 4.1.2 (KitKat)
OS Version
2014-11-06
Build Date
1
Countries
1
CSC codes
J (19)
Bootloader binary

Bootloader binary J (19). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab3 7.0 use bootloader binary U (30) (latest: T211MVJUBOB1). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T211MVJANK1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-T211M
    ZTM Brazil
    		T211MANK1 — — Download

    No matching downloads

    How to flash T211MVJANK1

    • T211MVJANK1 has bootloader binary J (19). Your device must run binary J (19) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal17.8 cm (7")
    • Display resolution1024 x 600 pixels
    • Rear camera resolution3 MP
    • Rear camera typeSingle camera
    • Front camera resolution1.3 MP
    • Wi-Fi standardWi-Fi 4 (802.11n)
    • Weight304 g

    Specifications of SM-T211, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    T211MVJANK1 is Android 4.1.2 (KitKat) firmware for Samsung Galaxy Tab3 7.0, released for Brazil (ZTM). Samsung built it on 2014-11-06.

    No. A newer build for SM-T211M is available: T211MVJUBOB1. Install it instead of T211MVJANK1 unless you need this exact version. The previous build was T211MVJANC1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab3 7.0 must be on bootloader binary J (19) or lower.

    This build uses bootloader binary J (19). It can be flashed on a Samsung Galaxy Tab3 7.0 running binary J (19) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab3 7.0

    No changelog details available.
    Model firmware by region