SM-T295N 1 country Android 9

Samsung Galaxy Tab A (8.0, 2019) T295NKSS3ATC1 Firmware

Name: Samsung Galaxy Tab A (8.0, 2019) (SM-T295N)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab A (8.0, 2019) T295NKSS3ATC1 is an Android 9 firmware for South Korea (KOO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T295NKSU2ASL2 https://samfirm.shop/build/T295NKSU2ASL2: Android updated from Android 9 (Pie) to Android 9; bootloader binary raised from 2 to 3, so after installing it there is no way back to older builds. A newer build for SM-T295N is available: T295NKSU4CUL1 https://samfirm.shop/build/T295NKSU4CUL1.

8.8/10 (39)4,395 times

Android 9

OS Version

2020-03-18

First release

other regions until 2020-03-19

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab A (8.0, 2019) use bootloader binary 4 (latest: T295NKSU4CUL1). If your device already runs binary 4, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: T295NKSS3ATC1

Model	Region	CSC Version	Build Date	Release date	Size	File name	Download
SM-T295N	KOO South Korea	T295NKOO3ATC1	2020-03-19	2020-03-26	2.102 GiB	SM-T295N_1_20200319123215_kdk0yhpdpf_fac.zip
SM-T295N	KOO South Korea	T295N3ATC1	2020-03-18	—	—	—

Device specifications

Display diagonal20.3 cm (8")
Display resolution1280 x 800 pixels
Processor frequency2 GHz
Rear camera resolution8 MP
Rear camera typeSingle camera
Front camera resolution2 MP
Wi-Fi standardWi-Fi 4 (802.11n)
Weight347 g

How to flash T295NKSS3ATC1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

T295NKSS3ATC1 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

T295NKSS3ATC1 is Android 9 firmware for Samsung Galaxy Tab A (8.0, 2019), released for South Korea (KOO). Samsung built it on 2020-03-18.

No. A newer build for SM-T295N is available: T295NKSU4CUL1. Install it instead of T295NKSS3ATC1 unless you need this exact version. The previous build was T295NKSU2ASL2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.102 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab A (8.0, 2019) must be on bootloader binary 3 or lower.

This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy Tab A (8.0, 2019) running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.