Samsung GALAXY Tab4 T331CZCU1AOD1
SM-T331C 1 country Android 4.4.2 (KitKat)

Samsung GALAXY Tab4 T331CZCU1AOD1 Firmware

Samsung GALAXY Tab4 T331CZCU1AOD1 is an Android 4.4.2 (KitKat) firmware for China (CHN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T331CZCU1ANI2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-T331C is available: T331CZCS1AQA1.

Download firmware
8.7/10 (455)4,480 times
Android 4.4.2 (KitKat)
OS Version
2015-04-16
Build Date
n/a
Security patch
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T331CZCU1AOD1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-T331C
    CHN China
    		T331C1AOD1 — —

    No matching downloads

    How to flash T331CZCU1AOD1

    • T331CZCU1AOD1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal20.3 cm (8")
    • Display resolution1280 x 800 pixels
    • Rear camera resolution3 MP
    • Rear camera typeSingle camera
    • Front camera resolution1.3 MP
    • Wi-Fi standardWi-Fi 4 (802.11n)
    • Weight323 g

    Specifications of SM-T331, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    T331CZCU1AOD1 is Android 4.4.2 (KitKat) firmware for Samsung GALAXY Tab4, released for China (CHN). Samsung built it on 2015-04-16.

    No. A newer build for SM-T331C is available: T331CZCS1AQA1. Install it instead of T331CZCU1AOD1 unless you need this exact version. The previous build was T331CZCU1ANI2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung GALAXY Tab4 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung GALAXY Tab4 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung GALAXY Tab4

    No changelog details available.
    Model firmware by region