Samsung Galaxy Tab E 8.0 T377VVRU1APB1
SM-T377V 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy Tab E 8.0 T377VVRU1APB1 Firmware

Samsung Galaxy Tab E 8.0 T377VVRU1APB1 is an Android 5.1.1 (Lollipop) firmware for United States (VZW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T377VVRU1AOL7, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-T377V is available: T377VVRU1CRF3.

Download firmware
9.3/10 (459)8,633 times
Android 5.1.1 (Lollipop)
OS Version
2016-02-02
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab E 8.0 use bootloader binary 7 (latest: T377VVRU1AOL7_OLA). If your device already runs binary 7, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T377VVRU1APB1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-T377V
    VZW United States
    		T377V1APB1 — — — Download
    SM-T377V
    VZW United States
    		T377VVZW1APB1 2016-03-04 1.83 GiB
    SM-T377V_1_20180615101640_lx074zznt9_fac.zip
    		Download

    No matching downloads

    How to flash T377VVRU1APB1

    • T377VVRU1APB1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 5.1.1
    • Display diagonal20.3 cm (8")
    • Display resolution1280 x 800 pixels
    • Processor frequency1.3 GHz
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Front camera resolution2 MP
    • Weight358 g

    Frequently Asked Questions

    T377VVRU1APB1 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy Tab E 8.0, released for United States (VZW). Samsung built it on 2016-02-02.

    No. A newer build for SM-T377V is available: T377VVRU1CRF3. Install it instead of T377VVRU1APB1 unless you need this exact version. The previous build was T377VVRU1AOL7.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.83 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab E 8.0 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Tab E 8.0 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 6 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab E 8.0

    No changelog details available.
    Model firmware by region