SM-T515N 1 country Android 10

Samsung Galaxy Tab A T515NKSS8BUD1 Firmware

Name: Samsung Galaxy Tab A (SM-T515N)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab A T515NKSS8BUD1 is an Android 10 firmware for South Korea (KTC, LUC, SKC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T515NKSU7BUA1 https://samfirm.shop/build/T515NKSU7BUA1: bootloader binary raised from 7 to 8, so after installing it there is no way back to older builds. A newer build for SM-T515N is available: T515NKSU8CVG4 https://samfirm.shop/build/T515NKSU8CVG4.

9.1/10 (463)13,410 times

Android 10

OS Version

2021-04-20

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 8. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: T515NKOS8BUD1

Model	Region	CSC Version	Build Date	Release date	Size	File name
SM-T515N	KTC South Korea	T515NOKR8BUD1	2021-04-20	2021-04-20	3.913 GiB	SM-T515N_1_20210407125835_xskyz6rcqx_fac.zip
SM-T515N	LUC South Korea	T515NOKR8BUD1	2021-04-20	2021-04-20	3.939 GiB	SM-T515N_1_20210407125935_gq5xmq85nq_fac.zip
SM-T515N	SKC South Korea	T515NOKR8BUD1	2021-04-20	2021-04-20	3.938 GiB	SM-T515N_1_20210407125805_mli1w4yw8k_fac.zip

Device specifications

Launched withAndroid 9.0
Display diagonal25.6 cm (10.1")
Display resolution1920 x 1200 pixels
Processor frequency1.8 GHz
Processor familySamsung Exynos
Rear camera resolution8 MP
Rear camera typeSingle camera
Front camera resolution5 MP
Wi-Fi standardWi-Fi 5 (802.11ac)
Weight470 g

How to flash T515NKSS8BUD1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

T515NKSS8BUD1 has bootloader binary 8. Your device must run binary 8 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

T515NKSS8BUD1 is Android 10 firmware for Samsung Galaxy Tab A, released for South Korea (KTC, LUC, SKC). Samsung built it on 2021-04-20.

No. A newer build for SM-T515N is available: T515NKSU8CVG4. Install it instead of T515NKSS8BUD1 unless you need this exact version. The previous build was T515NKSU7BUA1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab A must be on bootloader binary 8 or lower.

This build uses bootloader binary 8. It can be flashed on a Samsung Galaxy Tab A running binary 8 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 4 other builds of this model use the same binary, so you can switch between them in both directions.