Samsung Galaxy Tab Pro 10.1 T520XXSAQA2
SM-T520 2 countries Android 4.4.2 (KitKat)

Samsung Galaxy Tab Pro 10.1 T520XXSAQA2 Firmware

Samsung Galaxy Tab Pro 10.1 T520XXSAQA2 is an Android 4.4.2 (KitKat) firmware for Luxembourg (LUX), Netherlands (PHN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T520XXSAQA1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-T520 is available: T520XXUAOI2.

Download firmware
8.8/10 (457)8,909 times
Android 4.4.2 (KitKat)
OS Version
2
Countries
2
CSC codes
S (28)
Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab Pro 10.1 use bootloader binary U (30) (latest: T520XXUAOI2). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: MODEM
    ModelRegionCSC VersionSizeFile nameDownload
    SM-T520
    LUX Luxembourg
    		T520LUXAOJ1 — — Download
    SM-T520
    PHN Netherlands
    		T520PHNAOD1 — — Download

    No matching downloads

    How to flash T520XXSAQA2

    • T520XXSAQA2 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal25.6 cm (10.1")
    • Display resolution2560 x 1600 pixels
    • Display technologyLCD
    • Processor frequency1.9 GHz
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Front camera resolution2 MP
    • Wi-Fi standardWi-Fi 5 (802.11ac)
    • Weight469 g

    Frequently Asked Questions

    T520XXSAQA2 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Tab Pro 10.1, released for Luxembourg (LUX), Netherlands (PHN).

    No. A newer build for SM-T520 is available: T520XXUAOI2. Install it instead of T520XXSAQA2 unless you need this exact version. The previous build was T520XXSAQA1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab Pro 10.1 must be on bootloader binary S (28) or lower.

    This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Tab Pro 10.1 running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 10 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab Pro 10.1

    No changelog details available.
    Model firmware by region