Samsung Galaxy Tab4 10.1 T533XXS1BRI2
SM-T533 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy Tab4 10.1 T533XXS1BRI2 Firmware

Samsung Galaxy Tab4 10.1 T533XXS1BRI2 is an Android 5.1.1 (Lollipop) firmware for Germany (DBT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T533XXS1BPL2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. This is the newest build for SM-T533.

Download firmware
9.1/10 (480)8,754 times
Android 5.1.1 (Lollipop)
OS Version
2018-09-24
First release
other regions until 2018-11-29
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T533XXS1BRI2
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-T533
    DBT Germany
    		T533DBT1BRH1 2018-11-29 2018-11-30 1.183 GiB
    SM-T533_1_20181129111127_32fau3i6ub_fac.zip
    		Download
    SM-T533
    DBT Germany
    		T5331BRH1 2018-09-24 — — — Download

    No matching downloads

    How to flash T533XXS1BRI2

    • T533XXS1BRI2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal25.6 cm (10.1")
    • Display resolution1280 x 800 pixels
    • Processor frequency1.2 GHz
    • Rear camera resolution3 MP
    • Rear camera typeSingle camera
    • Front camera resolution1.3 MP
    • Wi-Fi standardWi-Fi 4 (802.11n)
    • Weight487 g

    Frequently Asked Questions

    T533XXS1BRI2 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy Tab4 10.1, released for Germany (DBT). Samsung built it on 2018-09-24.

    Yes. T533XXS1BRI2 is the newest build for SM-T533 on SamFirm. The previous build was T533XXS1BPL2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.183 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab4 10.1 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Tab4 10.1 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 12 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab4 10.1

    No changelog details available.
    Model firmware by region