Samsung Galaxy Tab S2 T719XXU1APDC
SM-T719 1 country Android 6.0.1 (Nougat)

Samsung Galaxy Tab S2 T719XXU1APDC Firmware

Samsung Galaxy Tab S2 T719XXU1APDC is an Android 6.0.1 (Nougat) firmware for United Arab Emirates (XSG). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T719XXU1APD7: Android updated from Android 6.0.1 (Marshmallow) to Android 6.0.1 (Nougat). A newer build for SM-T719 is available: T719XXS2BTJ4.

Download firmware
9.0/10 (460)4,272 times
Android 6.0.1 (Nougat)
OS Version
2016-04-29
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab S2 use bootloader binary 2 (latest: T719XXS2BTJ4). If your device already runs binary 2, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T719XXU1APDC
    ModelRegionCSC VersionSizeFile nameDownload
    SM-T719
    XSG United Arab Emirates
    		T719OJV1APD4 — — Download

    No matching downloads

    How to flash T719XXU1APDC

    • T719XXU1APDC has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal20.3 cm (8")
    • Display resolution2048 x 1536 pixels
    • Display technologySuper AMOLED
    • Processor frequency1.8 GHz
    • Processor familyQualcomm Snapdragon
    • Processor modelMSM8976
    • Rear camera resolution8 MP
    • Front camera resolution2.1 MP
    • Wi-Fi standardWi-Fi 5 (802.11ac)
    • Weight267 g

    Frequently Asked Questions

    T719XXU1APDC is Android 6.0.1 (Nougat) firmware for Samsung Galaxy Tab S2, released for United Arab Emirates (XSG). Samsung built it on 2016-04-29.

    No. A newer build for SM-T719 is available: T719XXS2BTJ4. Install it instead of T719XXU1APDC unless you need this exact version. The previous build was T719XXU1APD7.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab S2 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Tab S2 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 5 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab S2

    · Security patch update
    No changelog details available.
    · Security patch update
    No changelog details available.
    Model firmware by region