Samsung Galaxy Tab S5e T727AUCS6DWG4
SM-T727A 1 country Android 11

Samsung Galaxy Tab S5e T727AUCS6DWG4 Firmware

Samsung Galaxy Tab S5e T727AUCS6DWG4 is an Android 11 firmware for United States (ATT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T727AUCS5DWD1: bootloader binary raised from 5 to 6, so after installing it there is no way back to older builds. A newer build for SM-T727A is available: T727AUCU6DWH1.

Download firmware
8.8/10 (28)193 times
Android 11
OS Version
2023-07-21
Build Date
1
Countries
1
CSC codes
6
Bootloader binary

Bootloader binary 6. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T727AUCS6DWG4
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-T727A
    ATT United States
    		T727AATT6DWG4 2023-08-08 3.889 GiB
    SM-T727A_2_20230721152340_d7ev1nvh20_fac.zip

    No matching downloads

    How to flash T727AUCS6DWG4

    • T727AUCS6DWG4 has bootloader binary 6. Your device must run binary 6 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 9.0
    • Display diagonal26.7 cm (10.5")
    • Display resolution2560 x 1600 pixels
    • Display technologyOLED
    • Rear camera resolution13 MP
    • Front camera resolution8 MP
    • Wi-Fi standardWi-Fi 5 (802.11ac)
    • Weight400 g

    Specifications of SM-T727U, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    T727AUCS6DWG4 is Android 11 firmware for Samsung Galaxy Tab S5e, released for United States (ATT). Samsung built it on 2023-07-21.

    No. A newer build for SM-T727A is available: T727AUCU6DWH1. Install it instead of T727AUCS6DWG4 unless you need this exact version. The previous build was T727AUCS5DWD1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 3.889 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab S5e must be on bootloader binary 6 or lower.

    This build uses bootloader binary 6. It can be flashed on a Samsung Galaxy Tab S5e running binary 6 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab S5e

    No changelog details available.
    Model firmware by region