Samsung Galaxy Tab S7 FE 5G T736NKOU2CWB1
SM-T736N 1 country Android 13

Samsung Galaxy Tab S7 FE 5G T736NKOU2CWB1 Firmware

Samsung Galaxy Tab S7 FE 5G T736NKOU2CWB1 is an Android 13 firmware for South Korea (KOO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T736NKOU1CVL1: bootloader binary raised from 1 to 2, so after installing it there is no way back to older builds. A newer build for SM-T736N is available: T736NKOS9DYF1.

OS updates guaranteed until: Android 14Security updates until: Jun 1, 2025
Download firmware
9.2/10 (450)4,307 times
Android 13
OS Version
2023-02-20
Build Date
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab S7 FE 5G use bootloader binary 9 (latest: T736NKOS9DYF1). If your device already runs binary 9, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T736NKOU2CWB1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-T736N
    KOO South Korea
    		T736NKOO2CWB1 2023-02-20 5.176 GiB
    SM-T736N_2_20230214123130_l2i0gq2sva_fac.zip
    		Download

    No matching downloads

    How to flash T736NKOU2CWB1

    • T736NKOU2CWB1 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal31.5 cm (12.4")
    • Display resolution2560 x 1600 pixels
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Front camera resolution5 MP
    • Wi-Fi standardWi-Fi 5 (802.11ac)
    • Weight608 g

    Specifications of SM-T736B, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    T736NKOU2CWB1 is Android 13 firmware for Samsung Galaxy Tab S7 FE 5G, released for South Korea (KOO). Samsung built it on 2023-02-20.

    No. A newer build for SM-T736N is available: T736NKOS9DYF1. Install it instead of T736NKOU2CWB1 unless you need this exact version. The previous build was T736NKOU1CVL1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 5.176 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab S7 FE 5G must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy Tab S7 FE 5G running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab S7 FE 5G

    No changelog details available.
    Model firmware by region