Samsung Galaxy Tab S 10.5 T800XXU1CPL2
SM-T800 1 country Android 6.0.1 (KitKat)

Samsung Galaxy Tab S 10.5 T800XXU1CPL2 Firmware

Samsung Galaxy Tab S 10.5 T800XXU1CPL2 is an Android 6.0.1 (KitKat) firmware for Iraq (MID). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T800ZCU1CPK7: Android updated from Android 6.0.1 (Marshmallow) to Android 6.0.1 (KitKat). A newer build for SM-T800 is available: T800DDU1CVH2.

Download firmware
8.8/10 (457)4,245 times
Android 6.0.1 (KitKat)
OS Version
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T800XXU1CPL2
    ModelRegionCSC VersionSizeFile nameDownload
    SM-T800
    MID Iraq
    		T800OJV1CPL2 — — Download

    No matching downloads

    How to flash T800XXU1CPL2

    • T800XXU1CPL2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal26.7 cm (10.5")
    • Display resolution2560 x 1600 pixels
    • Display technologySuper AMOLED
    • Processor frequency1.9 GHz
    • Processor familySamsung Exynos
    • Processor model5 Octa
    • Rear camera resolution8 MP
    • Front camera resolution2.1 MP
    • Wi-Fi standardWi-Fi 5 (802.11ac)
    • Weight465 g

    Frequently Asked Questions

    T800XXU1CPL2 is Android 6.0.1 (KitKat) firmware for Samsung Galaxy Tab S 10.5, released for Iraq (MID).

    No. A newer build for SM-T800 is available: T800DDU1CVH2. Install it instead of T800XXU1CPL2 unless you need this exact version. The previous build was T800ZCU1CPK7.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab S 10.5 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Tab S 10.5 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 86 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab S 10.5

    • GPS
    The stability has been improved.

    No changelog details available.

    - The latest Android security patch has been applied.
    ㆍDevice security has been further enhanced.

    No changelog details available.
    Model firmware by region